Ask Blue anything.
Get answers you trust.

Every answer references the place in the document or video pulled from. If it's not in the documentation, Blue won't make it up.

Accurate answers
in seconds

Blue searches across manuals, parts lists, wiring diagrams, training videos and even emails to give you a clear, accurate answer.

AI Answers & Training
POV Training
How do I reset the tilt sensors on a JCB scissor lift?
Sourced from 1 manual + 1 expert video
How do I reset the tilt sensors on a JCB scissor lift?
Answer
1. Raise the platform and secure it
Raise using ground controls and secure with a safety stop or prop. You need access to the scissor stack.
Expert video
R. Delaney · 0:15
2. Locate the gray tilt sensor
Find it between the scissor stack, right in the middle, on the cross brace.
p.3-8
JCB S3246E Service Manual
Section 3 · Tilt Sensor Location
3. Run a wire from the main battery
Run a jumper wire from the main battery to the center screw of the tilt sensor.
4. Apply 24V to the center screw
Apply 24 volts directly to the sensor's center screw. This resets the zero position. Machine must be level.
Expert video
R. Delaney · 1:42
5. Complete the reset
Touch wire to center screw to complete. Lower platform and test controls to confirm fault cleared.
p.3-10
JCB S3246E Service Manual
Section 3 · Calibration
Service Manual p.3-8, 3-10
Expert video — R. Delaney

Step-by-step instructions

Get an organized walkthrough curated from all the available sources from yourknowledge repository.

📋
Step-by-step
Deutz TCD 3.6 L4 fuel system service
Sourced from Deutz Workshop Manual 0312 3965 en · Section 3.2
1
Shut down engine and wait 30 seconds
Common rail system operates at up to 2000 bar. Pressure may remain in the rail after shutdown.
§3.2.1
Deutz TCD 3.6 L4 Workshop Manual
Safety Information · Fuel System
2
Clean engine and engine room before opening fuel system
Engine must be dry. Use lint-free cloths only. No compressed air on open fuel system.
3
Open fuel connections slowly, never abruptly
Residual pressure may still be present. Loosen screw connections with extreme caution.
4
Cap all openings immediately after removal
Use approved stoppers/caps. Remove caps only immediately before reinstalling. Dispose after single use.
Expert video
R. Delaney · 1:12
5
Bleed the fuel system after reassembly
Per operation manual, Chapter 6. Verify no leaks at all connections before starting.

Turn expert repairs into
just-in-time training

When a senior tech records a job, that recording becomes training material for the rest of the team.

🎓
POV Training
Expert video library
12 expert recordings · 3 technicians
Tilt sensor reset — JCB S3246E
R. Delaney · 2:34 · 4 steps
Hydraulic hose replacement — Genie GS2632
M. Torres · 4:12 · 6 steps
Coolant system flush — Takeuchi TL12R
K. Morrison · 3:05 · 5 steps

More ways to use Blue

Blue answers questions from your documents. But it also learns from every recording your team makes, building a knowledge base that gets richer over time.

Operations
Business Insights
Blue tracks patterns across every job your team records. Recurring equipment issues, time on task, common failure modes. Operational data that used to require a consultant.
Reference
Specs & Tolerances
Torque specs, clearances, fluid capacities, wire gauges. Ask by voice and get the exact number from the manual.
Parts
Parts Lookup
Say the model number or point the camera at a part. Blue finds the part number, cross-references, and availability from your catalogs.
Diagrams
Wiring & Schematics
Ask Blue to pull up a wiring diagram or schematic mid-job. It finds the right page from the right manual.
Safety
Safety Procedures
Lockout/tagout steps, PPE requirements, OSHA standards for a specific task. Blue knows your safety SOPs.
Language
Ask in Any Language
Ask in Spanish, get the answer in Spanish. Blue works in the language your techs speak naturally.

Built into every answer

Recognize text, labels and barcodes

Fully configurable

Video timestamps

Every answer cites its source

Hands-free, voice-activated

Supports OSHA, NIOSH, ISO and more

Translates 50+ languages

Searchable across all jobs